Coral Castle & Free Energy Research



The “Theory of Magnetic Instability”, or TOMI from now on, is a phenomenal piece of research. Mr. Harris was able to show in his paper that a magnetic pole can be isolated, and that there are two levels of energy in a magnet not just one.

Let me clarify. James Clerk Maxwell’s second law of electricity and magnetism dictates that there is no isolated magnetic pole. “Monopole” So a tri-pole interaction is disallowed as a result of this thinking. Because of course, no monopoles exist in the universe that we know of. However, any pole that is in a magnetic field, and is isolated can effectively act as a monopole. This is the heart of TOMI.

To paraphrase TOMI and give you a better understanding of what this means, let’s do an experiment. Take three bar magnets magnetized through their lengths. Set two of them side by side in an attracting position as seen in the next figure.

Now place the third magnet in between as seen. You will see that the north pole of the magnet in the center is only interacting with the bar magnet on the left, that would be a tri-pole configurment. The same would be true of the South pole of the center magnet interacting with the right hand magnet.

Now, Let’s name these things so they can be understood easier. The two magnets that are parallel to one another we will call “tracks” (paths which can be followed). The center magnet we will call the “runner” (the free moving piece of our model for now).

The above picture is the basis for all TOMI systems. However this setup is not yet a TOMI model. The runner placed into the tracks as you see, will immediately move to a midpoint in the tracks and STOP!

This is an experiment that shows “magnetic stability”. Meaning that when the push from the bottom half of the tracks equals the pull from the top half of the tracks, motion ceases. The runner magnet has found a neutral or dead zone and we see it seize in Magnetic Lock! .

However in a TOMI setup, there never is a “stability”. There is always instability. Let me explain.


The above is a magnet. You will notice that it has two poles and a dead zone in between. (when in a tri-pole interaction) However in TOMI we use that space in between by creating cross cuts perpendicular to the end poles. This in effect gives us a “manypoled” magnet. As you see below.


This crosscuting gives the magnet it’s “instability”. By that statement I mean for you to understand that when a third pole is brought into play it does not find a resting place or dead zone in the center of the bar magnets magnetic fields. Instead it will want to continue to move the entire length of the magnets.

There is an important thing to know about the crosscuts that you have introduced and how they come into play with the runner magnet. The runner magnet must be larger in field surface area than one of the new miniature magnets that the crosscuts have created for the “instability” to happen. It is also important to only cut one face of each track in this setup.

As you can see in the figure right, the runner will want to travel the entire distance of the new TOMI tracks. This in effect doubles the ability to do work in a magnet. If you want to argue that the cross cutting added energy to the magnet then I will ask you to explain why the uncut faces of the TOMI does not make the runner travel the full length of the tracks. Or for the sake of proof grind the crosscuts off, you will never see anything but a loss despite the fact that you have argued that doing work just added energy. Notice that this process of crosscutting then grinding off the cuts, reduces mass, which in accord with Energy being equivalent to Mass, should dictate a continuous loss or destruction of energy. Wrong!

Take those same ground down magnets and cross cut new lines in them and the runner magnet will once again travel the whole distance.

These tracks will work on a flat plain, but will work even more amazingly so at a 90 degree upright position, literally levitating the runner magnet to the tracks full height.

These tracks could be placed on the sides of a ramp and produce work. Place your runner at the base of the ramp, it will then climb the ramp. If the TOMI tracks are placed hanging just over the edge of the top of your ramp, the runner will climb to the top of the ramp and then fall off the edge. By placing another ramp at the base of the first one, the falling runner will basically reset itself and start climbing this new ramp. And on and on......

Example of ramps in series.


Mr. Harris devised several methods to use his discovery one in which a runner would climb a ramp then fall through a trap door and trip a latch to allow the ramp to rotate thereby resetting itself to climb the ramp again and start all over.

This brings us to my discoveries. I have been building my own and trying to duplicate other free energy devices for some time. I have been trying to work the TOMI principle into them since I found the paper on the internet in late 2000 that furthers the coral castle creation.

I have seen other concepts and devices that are truly amazing in their ability to create energy from seemingly nothing. However most of the devices used timing switches and electric circuits. What I wanted to do was prove that energy could be produced from permanent magnets alone without the need for fancy timing gizmos and wiring that could hide a lie. I wanted basic, basic, and nothing else.

I started to build devices like the Minato bicycle wheel, and the Robert Callaway wheel designs. These and others like them were very hard to try and duplicate due to their needing an amazing amount of patience to just tune the flow of the magnetic fields. Another machine that seemed almost impossible to tune was the Wesley Gary magnetic motor. Mr. Gary was a gentleman from Pennsylvania that lived in the late 1800’s. Some of his patents would blow your mind just by how simple they are and that the logic behind them is totally solid.

While working with these devices I started to notice common threads of thought. One device would use a lever to block the magnetic attraction between two magnets while another would simply taper the field away from other magnets while spinning away.

What these concepts were trying to do was to overcome the major obstacle of the permanent magnet perpetual motion machine... The “magnetic lock”.

This is the point in a cycle where two or more magnets would come into play and not want to let go of each other. Thus the kinetic energy built up within the device would have to be great enough to break the magnetic lock, and reset the device so as to start another cycle. Much easier said that done until MAG-GEN.

Mag-Gen is needed in our society now!

Page 1 | 2 | 3 | 4